Music, Sound, and Audio Technology
Production Design for Dialogue Recording: How Other Departments Can Help the Sound Dept. Improve the Quality of Recorded Dialogue
By Staff
posted Oct 16, 2009, 12:55
Sound for film and video, production design for dialogue recording, audio recording tips, audio recording techniques, sound recording tips, sound recording techniques, production sound, production recording, learn more about audio.
Check out this article in the print edition of StudentFilmmakers
Magazine, July 2007. Click
here to get a copy and to subscribe >>
Production
Design for Dialogue Recording:
How Other Departments Can Help the Sound Dept. Improve the Quality
of Recorded Dialogue
by Fred Ginsburg C.A.S. Ph.D. MBKS
Most articles that deal with production sound recording for video and film tend to cover microphones and recording/mixing techniques. I am not going to cover audio from the Sound Mixer�s perspective, but rather from the contributions of other departments.
Why should other departments care about improving audio? After all, except
for editing, the sound is not their responsibility, right?
Filmmaking is very much like being on a naval warship. If anyone messes
up and the ship takes a serious hit, then everyone goes down. Even though
you may have done a great job in your department, and contributed heavily
towards one aspect of the film � if one major area of the overall production
quality is poor, and the film fails to be accepted for festivals or distribution
� then all of your efforts will remain a secret. On the other hand, if
a film you worked on garners awards and praise � then having it on your
resume is bound to help your career!
Bad audio will certainly sink an otherwise good film.
That being said, let�s look at how other departments can help the Sound Department improve the quality of the recorded dialogue.
Set construction for filmmaking is different than general contracting. Whereas the Zoning Board insists on 90 degree angles and perfect verticals, the law of acoustics prefers things to be several degrees off from perfect. Walls in a set should never join at exactly ninety degrees, but should extend outward so that sound waves reflect away from the set. Avoid parallel wall surfaces so that sound waves do not careen back and forth.
Allow the walls to tilt a few degrees from perfect vertical. This will also reduce room reverb and echo.
The camera lens will never reveal your set is a trapezoid rather than a perfect rectangle. The slight variance of angle appears on screen as linear perspective (and not bad carpentry).
Do not use hard drywall to construct walls and flats. Instead, use a more absorbent media, such as �sound deadening board� which is like a compressed cardboard and sucks echo like a sponge. If the original construction was hard wood or drywall, then consider covering it with a thin layer of upholstery foam, deadening board, carpet padding, or something soft � and then staple gun some fabric over it all for visual finishing. You can paint over the fabric, if needed.
Wherever possible, put some carpet on the floor to eliminate footsteps and reduce echo. I once worked on a show that had scenes in a Marine barracks. The image of a platoon of soldiers running about on plush carpet just wouldn�t be realistic; but nothing in the rulebook said the carpet couldn�t look like hardwood flooring! We used a fairly flat indoor/outdoor carpet, and the set painters worked their magic to add the illusion of plank lines, nail holes, and other elements. The Sound Department got their �carpet� and the Production Design got their �hardwood floor!�
Plan ahead for boom shadows on walls. A plain wall will turn into a projection screen of body shadows and boom shadows if left naked. Set Design should add textures to the walls, fixtures or furnishings, and create natural patterns of light and dark to hide or mask production shadows. The shadows will still be on the wall, but the audience should not be able to quickly discern and identify them as having been created by the filmmakers.
Furniture placement is another key factor. Couches and chairs should never be too close to a wall, or else shadows are a certainty. Move the actors and their seating towards the center of the set, so that the lighting on them can be barndoored, so as to �bury� the shadow of the barndoors where the wall and floor meet. Any shadows cast by the actors� heads or the boom poles will not show up on the background wall. Then use a separate �background light� to illuminate the wall, maybe even adding a cukaloris to create some patterns. If the actors are positioned too close to the walls, then there would be no way to separate their lighting from that hitting the wall behind them.
If the actors do have to perform close to a wall, then the Sound Department has to be careful not to reveal the boom shadow, (or use alternative miking such as lavaliers or planted mics). This is where it is valuable to have fixtures, patterns, and textures on the wall to help hide the shadows.
Tables and desktops should be covered with a soft padding and then draped with a tablecloth of some sort. This reduces audio reflections up from the hard surface, and eliminates the clinking and clanking of items being manipulated.
Chairs that are out in the open may be difficult to reach with a boom mic if all the rest of the action is somewhere else in the room. Establishing a side table, ottoman, or magazine stand can come in very handy later on. It can provide a convenient place to hide a mic or even a light � not to mention blocking the frame in order to hide the presence of a power or audio cable. Ditto with tall plants, coat racks, and other furnishings.
Wardrobe plays a major role in sound recording. Choice of fabric and
style will affect the use of body worn lavalier mics, be they hard-wired
or wire-less. There are two types of clothing noise: acoustic and contact.
Acoustic clothing noise is created when the clothing elements themselves rub against each other and generate noise from friction or fabric crunching. Natural fibers, such as wool and cotton, are quieter than synthetic fibers. Starch may look neat, but is noisy. Use as little as possible, and only in strategic places where it is necessary, such as collars, center strips (where the buttons are), and shirt pockets. Excess starch can be neutralized by a puff of water from a plant spritzer.
Excess jewelry should be avoided, or at least replaced by plastic or rubber look-alikes.
Contact clothing noise is when the wardrobe physically rubs against the microphone head or leading several inches of cable. Reduce this noise by immobilizing any clothing on either side of the mic placement. Usually we accomplish this by means of a wad (actually a neatly formed triangle) of cloth camera tape, sticky side out, and with safety pins. Misting the area around the mic helps soften the starch and clothing fibers.
Often, the Sound Department can prevail upon Wardrobe to create special hidden pockets for concealing the wireless mic bodypacks, especially when the same costumes are worn repeatedly. Sometimes they will also make special button holes or access points for threading lavaliers through outer layers of clothing (such as winter coats, suit jackets, etc.) For example, a lavalier can be rigged through a small opening behind the chest pocket of a suit coat or a lab coat and then �hidden� in the top of a prop �pen� that innocently protrudes from that same pocket.
If talent is scantily clad, then the Make-Up Department may be called
in to help. Mics can be hidden in the hair or beard. Or under a wig. Lavaliers
sequestered inside a bra or halter top still have to be �wired� down to
the hip or lower. Usually, we just run the cable to the far side of the
body, least likely to be on camera, and then tape the wire down using
a clear, medical tape. Make-up is then applied over the strip of tape
to blend it in nicely with the exposed torso. This suffices well for long
shots. In a close-up where the skin would be fully revealed, it would
be a tight enough frame to use the boom mic instead of the lavalier!
Fred Ginsburg C.A.S. Ph.D. MBKS is a Production Sound Mixer with over two decades of experience on feature films, episodic television, national commercials, corporate, and government. He is the author of over 90 articles and Guide to the Nagra 4.2 and Production Sound Recording. Fred is president of the Equipment Emporium Inc. and co-Executive Director of the National Association of Forensic Video. He also teaches at the California State University Northridge. |
This article may not be reprinted in print
or internet publications without express permission of StudentFilmmakers.com.
The above photos may not be copied or reproduced.
Check out this article in the July 2007print edition of StudentFilmmakers
magazine, page 34.
Click
here to get a copy of the July 2007 Edition, so you can read
and enjoy all of the excellent articles inside.
About StudentFilmmakers Magazine and StudentFilmmakers.com
Learn about the Latest, Cutting-Edge Technologies and Techniques at StudentFilmmakers.com
and StudentFilmmakers Magazine, the #1 Educational Resource for
Film and Video Makers covering various topics with special focus
on: Development, Pre-Production, Production, Post Production, Distribution.
Article categories include: Cinematography, Lighting, Directing, Camerawork,
Editing, Audio, Animation, Special FX, Screenwriting, Producing, and more.
Watch, upload, and share your films and videos in the video section at:
networking.studentfilmmakers.com/videos.
Network and connect with filmmakers around the globe using the Filmmakers
Social Networking Site at: networking.studentfilmmakers.com.
Share your ideas, post your questions, and find answers in the online
interactive forums moderated by experts at: www.studentfilmmakers.com/bb.
StudentFilmmakers.com (www.studentfilmmakers.com)
also produces and hosts film, video, and screenwriting festivals and contests,
as well as educational workshops and seminars. Get the magazine, read
the e-newsletter, and participate in the online portal and resource with
free tools for film and video makers of all levels around the globe. With
the technology changes coming faster and faster, we are all students.
StudentFilmmakers magazine would like to hear from you!
Click here to
share your comments and feedback about the magazine, monthly editions,
your favorite articles, and your favorite topics.
We always welcome and appreciate your Reader
Comments. View them here,
and send yours
to the editorial team today!
www.studentfilmmakers.com © 2004-2005. All rights reserved.
A division of Welch Integrated, Inc.